Página 215 - abchance

Versión de HTML Básico

Tool Repai r & Storage – 2500
Phone: 573-682-5521 Email: hpsliterature@hubbell.com Web: hubbellpowersystems.com
Page 2503
September 2012
Features & Applications
• Strong solvent for water and conductive  contaminants
• Safe to Earth’s ozone layer – free of chlorinated
hydrocarbons
• More economical, easier to work with due to lower
evaporation rate
• Pleasant, orange scent from citrus-based biodegradable
component
Less Waste
• Contains no water and absorbs water in its presence
• Removes twice as much water as the original Moisture
Eater
• Minimizes chemical waste
• Unique formula of Moisture Eater II gives it a much
lower evaporation rate than original formula and other
hot-line tool cleaners
Epoxiglas
®
Cleaning Kit
Features & Applications
• Essential for care and maintenance of Epoxiglas
®
tools
• Also cleans insulated boom sections of aerial lift trucks
• Helps to ensure maximum life of Epoxiglas products
• Do not use on Gel-Coat or painted boom surfaces
4 Parts Of The Kit
1. Moisture Eater II — This cleaner should be used
on contaminated Epoxiglas during general tool
maintenance and in preparation for reglossing a tool’s
surface. Moisture Eater removes moisture and a wide
variety of contaminants such as dirt, tar, grease, tree
sap, light metal rubbings and old surface coatings
without harming the Epoxiglas material
2.  Abrasive Cleaning Pads — These pads are used
in conjunction with Moisture Eater II to remove
contamination that clings to the tool or contamination
ground into scars and scuffs in the tools surface. Gloss
restorer must be applied after using these pads since
cleaning with Moisture Eater II will remove the glossy
finish on the tool as well as contamination. The pads
may also be used on metal parts to remove oxides and
surface corrosion
3. Gloss Restorer Kit — This kit consists of two parts.
When mixed and applied to the surface of a cleaned
Epoxiglas tool they combine to form a clear, tough
coating that replaces the original gloss and protects
against contamination and moisture
4. Hot Stick Wiping Cloths — Silicone impregnated
cloths are used to wipe down mildly contaminated
Epoxiglas, removing dust and dirt, and depositing a
thin protective film on the surface of the tool. They
give an added measure of protection when used after
recoating with gloss restorer
Available in 1-gallon jug
as
Catalog No. C4002364
(also comes in Epoxiglas
Cleaning Kit).
Moisture Eater II
Cleaner-Solvent
for hot-line tools, line hose
and blankets
1
2
3
4
Description
 Moisture Eater II Cleaner, 1 gal./4.23 liters
 Epoxiglas Cleaning Kit*
The above kit consists of the following items:
(Each may also be ordered separately.)
 Moisture Eater II Cleaner, 1 gal./4.23 liters
 Abrasive Cleaning Pads (box of 20)
 Gloss Restorer Kit
 Hot Stick Wiping Cloth (*2 in Kit above)
 Catalog No.
C4002364
C4002365
C4002364
C4001166
C4001520
M1904
1
2
3
4
Environment-Friendly Advantages
• New formula consists of two solvents:
o One for oils, waxes and silicone-type contamination
o One for moisture contamination
• This combination is ideally suited for cleaning hot-line
tools
• A by-product of citrus fruit, one component is
biodegradable; the other component protects it from
decomposing until used
• Reformulation eliminates chlorinated solvents
harmful to Earth’s ozone layer
• For more technical details, refer to Material Safety
Data Sheet ABC/C56